Tri-fold hard folding tonneau cover installation guide

Key Features

• Durable Material
• Easy, no drilling installation
• Stylish design
• Strong protection against weather exposure and theft
• Simple operation with quick-release latches
• Can be easily folded down or removed to accommodate oversized loads

Item List

Bag Buckles × 1
Plastic Sliding × 1
T Bolt × 1
Handles × 4
Seal Strip × 1
Hex Screws × 4
Bag Buckles Mounts × 2
Rubber Block × 2
Hex Key 3.0mm × 1
Aluminum Buckles × 2
Knobs × 2
Tonneau Cover × 1

• Note: Only for Toyota/Nissan/Jeep with utility track, the following items are included.

Set Screws × 12
Hex Key 2.5mm × 1
Aluminum Blocks × 6

Before Installation

Warning

• Please wear gloves for package opening and cover installation.
• Keep this product away from children.

Caution

• Only install the product when the vehicle is stationary and on level ground.
• Remove unnecessary items on the truck bed and/or attach them to the side rail during installation.
• Before folding and unfolding the panels, make sure the components are secured and remove all other items including any packages, tape, etc.

Tri-fold hard folding tonneau cover installation guide

Step 1: Wipe clean the truck bed before sticking the seal strip and aligning both ends equally. Flush with the edge.

Step 2: Please align the buckle mounts according to the hole's position in the front bar of the tonneau cover, and fasten the screw with the hex key. Place the tonneau cover on top of the truck bulkhead.

• Step 3-a: Slide the aluminum blocks into the utility track, align it with the front clamp's position, and tighten the screws.

• Step 3-b: On the first panel, use these items to assemble two front clamps(insert aluminum buckles and knob through pre-installed T bolt). Slide them towards the side trail and tighten on both ends.

Step 4: If your truck has a utility track, please secure the clamps on the aluminum blocks.

Step 5: Before unfolding the second panel, insert the handles into the pre-installed bolts. Then fold down the second panel.

• Step 6-a: Slide the aluminum blocks into the utility track, align it with the position of the handles, and tighten the screws. Secure the handles on the aluminum blocks.

• Step 6-b: Slide the handles towards the truck bed rail. Push down and secure the clamps on both ends.

Step 7: Spread the rubber block a little so it is easier to insert into the slot. Repeat it on the other side. (If applicable, before unfolding the last panel, insert handles into the pre-installed T bolts.)

Step 8: If applicable, fold down the last panel, then slide the handles towards the truck bed rail. Then push down and secure the clamps on both ends.

After Installation

Warning

• DO NOT drive with a tailgate completely or partially open. Tonneau cover MUST be in either a completely closed or opened position when the vehicle is in movement.
• In the closed position, shut the tailgate before the rear panel is closed. All panels MUST be flat and all latches MUST be securely engaged to the tonneau side rail.
• In the opened position, all latching handles MUST be secured before folding the panel. Attach the buckle clips by inserting them into the buckle ends located on the top of the panel.
• Whenever the latches are not attached to the truck bedside rail, they MUST be secured in the slots on the panel.

Caution

• Before folding the panels, remove all other items including ice, snow, leaves, branches, etc.

How to maintain a hard tonneau cover?

We use durable material to build the Tonneau Hard Folding Cover, some simple maintenance is enough to keep the cover’s performance and extend its lifespan.

Check Bolts Engagement

• We recommend the user to check the cover is securely attached to the truck bed from time to time. Look for any loose bolts due to road vibrations, cargo contact, etc. Make sure all mount points of the cover are properly attached.

Inspect the Handles

• We recommend the user to periodically check the handles on each panel. Remove any dirt or dust from the handle and side rail to allow the component to work without unnecessary resistance. Lubricate the handles from time to time so the handles can move freely during engaging and disengaging.

Clean the Surface

• Use a sponge or soft cloth with water and soap to gently remove any dust or dirt off the surface.